NASA SBIR 2016 Solicitation

FORM B - PROPOSAL SUMMARY


PROPOSAL NUMBER: 16-1 S3.07-8563
SUBTOPIC TITLE: Thermal Control Systems
PROPOSAL TITLE: Loop Heat Pipe Manufacturing via DMLS for CubeSAT Applications

SMALL BUSINESS CONCERN (Firm Name, Mail Address, City/State/Zip, Phone)
Advanced Cooling Technologies, Inc.
1046 New Holland Avenue
Lancaster, PA 17601 - 5606
(717) 295-6061

PRINCIPAL INVESTIGATOR/PROJECT MANAGER (Name, E-mail, Mail Address, City/State/Zip, Phone)
Dr. William Anderson
Bill.Anderson@1-act.com
1046 New Holland Ave.
Lancaster, PA 17601 - 5606
(717) 295-6104

CORPORATE/BUSINESS OFFICIAL (Name, E-mail, Mail Address, City/State/Zip, Phone)
Dr. William Anderson
Bill.Anderson@1-act.com
1046 New Holland Avenue
Lancaster, PA 17601 - 5606
(717) 295-6104

Estimated Technology Readiness Level (TRL) at beginning and end of contract:
Begin: 3
End: 4

Technology Available (TAV) Subtopics
Thermal Control Systems is a Technology Available (TAV) subtopic that includes NASA Intellectual Property (IP). Do you plan to use the NASA IP under the award?
No

TECHNICAL ABSTRACT (Limit 2000 characters, approximately 200 words)
Advanced Cooling Technologies, Inc. (ACT) proposes to develop a low-cost Loop Heat Pipe (LHP) evaporator using a technique known as Direct Metal Laser Sintering (DMLS), otherwise known as 3D printing, to produce low-cost LHPs to be used in CubeSat and SmallSat applications. The wick structure in an LHP assumes the role of a pump in a standard loop, pumping liquid from the lower pressure condenser to the higher pressure evaporator by capillary forces. The overall thermal performance of the system is therefore highly dependent on the in-situ characteristics of the wick structure. Current LHP wick manufacturing and installation processes are cumbersome, labor intensive, and suffer from a low yield rate. Specifically, the primary wick�s hydrodynamic characteristics and sealing integrity to the envelope are critical to heat transport, start-up, shut down and overall reliability. It is estimated that the cost to produce an LHP evaporator, including the attachment of the bayonet, secondary wick and compensation chamber, accounts for approximately 75% of the total system�s manufacturing cost. By 3D printing an evaporator envelope with an integral porous primary wick structure, the overall complexity and cost of the design can be significantly reduced.

POTENTIAL NASA COMMERCIAL APPLICATIONS (Limit 1500 characters, approximately 150 words)
Ammonia and propylene LHPs are currently used in most NASA and commercial satellites. In comparison with Constant Conductance Heat Pipes (CCHPs), they carry much higher powers (1 kW vs. 100 W) over longer distances (10 m vs. 2-3 m). They also are better suited for ground testability. An LHP can operate with the evaporator 2 meters above the condenser, versus 2.5 mm for a CCHP. Their main drawback is that they are two orders of magnitude more expensive to fabricate and test than CCHPs. Fabricating, machining, and inserting the primary and secondary wicks into the pump is the bulk of the fabrication expense (The remainder of the LHP is just plumbing). The first benefit of the proposed evaporator/wick fabrication will be a significant reduction in cost of LHPs supplied to NASA. A second benefit of reduced costs it that LHPs will be much more attractive for the smaller satellites, such as SmallSat and CubeSat, that NASA is now considering for future missions. The overall budget for these satellites is severely constrained when compared to the larger satellites that NASA has fabricated in the past. LHPs have not been considered in the past for these small satellites, partially due to their high cost. The reduced fabrication costs will allow ACT to fabricate smaller LHPs for these smaller satellites, at a price that is acceptable with their smaller budgets.

POTENTIAL NON-NASA COMMERCIAL APPLICATIONS (Limit 1500 characters, approximately 150 words)
ACT is one of only two companies in the United States that sells heat pipes, Variable Conductance Heat Pipes (VCHPs), and LHPs to the government and commercial customers for spacecraft thermal control. The benefits for the Air Force are similar to the benefits for NASA, both for today�s spacecraft, and for smaller satellites in the future. The commercial communications satellite market is the current primary market for LHPs. For example, one prime uses 5 to 6 LHPs on each satellite, and would also benefit from reduced costs.
Finally, Universities are able to fabricate their own CubeSats for research in space; however, their budgets are much too limited to allow them to use LHPs as a thermal control tool. In addition, these SmallSats have no need for the high powers and long lengths of current LHPs. They could benefit from small size LHPs, if the cost can be significantly reduced. ACT plans to explore this market, after satisfying the higher end government and commercial markets.

TECHNOLOGY TAXONOMY MAPPING (NASA's technology taxonomy has been developed by the SBIR-STTR program to disseminate awareness of proposed and awarded R/R&D in the agency. It is a listing of over 100 technologies, sorted into broad categories, of interest to NASA.)
Active Systems

Form Generated on 04-26-16 15:14